Get exclusive volume discounts, bulk pricing updates, and new product alerts delivered directly to your inbox.
By subscribing, you agree to our Terms of Service and Privacy Policy.
Direct access to our certified experts
Coating function
Suitable system: NCM, LFP, LCO, LMO, Graphite, Silicon carbon and other systems battery coating
Coating method: Continuous and intermittent coating (Transfer coating machine)
Oven section: 1m/section
Coating speed: 0~0.5m/min (Depending on the drying state)
Base material thickness: Al foil : 8～30um, Cu foil : 8～30um
Roller width: 330mm
Effective coating width: ≤280mm
Coating roller:Φ120mm
Squeegee roller: Φ80mm
Coating accuracy: ±3um
Weight accuracy of double-sided coating (mg/cm2): Coating center value ±1.0%
Suitable for slurry viscosity: 2000~12000 (mPas)
Single side coating dry thickness range: 20-200μm
Solvent properties
Oily solvent
NMP(s.g=1.033,b.p=204℃)
Aqueous solvent
H2O/NMP(s.g=1.000,b.p=100℃)
Suitable for solid content range: 20~85%
Coating size accuracy (mm): L≤±1, W≤±0.5 (L: length direction, W: width direction)
*Introduction to the structure of coating parts：
1. Integral unwinding, machine head mechanism：
Over roller installation structure: Steel frame firmly installed
Over roller surface treatment: Surface oxidation of metal aluminum roll
Tension control system:Automatic control of constant tension, tension range 0 ~ 50N, servo motor control
Correction method: Automatic EPC control,Stroke 50mm
Feeding Unwinding material method
The material roll is fixed by a 3-inch inflatable shaft；
Unwinding single air expansion shaft
Maximum unwinding diameter: Ф250mm
Maximum load of inflatable shaft: 80Kg
Number of unwinding and inflation shafts: 1Pcs
Main drive motor: Servo motor
Roller surface treatment: Surface oxidation of metal aluminum roll
Scraper structure: Double-sided comma scraper
Coating roller (steel roller): Hard chrome plating
Back roller (rubber roller): The surface is wrapped with imported EPDM
Scraper intermittent height adjustment:Manual adjustment;
Single head position: Installation and operation before drying tunnel
2. Coating drying tunnel
Oven structure:Double-layer independent heating, arranged up and down
Oven length: 1 meter / section
Material: SUS304 stainless steel
Temperature control: Divided into normal working temperature control, over-temperature monitoring and alarm protection control, and cut off the heating main power supply; each section is completely independent control
Heating method: Analog signal control power heating, hot air circulation structure
Heating power of single section oven: 6KW
Temperature in drying tunnel: Design Max150 ℃, temperature difference in single section oven≤ ± 2.5 ℃
Blowing method:Upper and lower air blowing, common heating body for upper and lower air chamber
Wind nozzle structure: The nozzle slot is slotted by a special mold
Fan control: Contactor control
Heating control: solid state relay
Fan material: SUS304 stainless steel
Solvent recovery system: Optional
*Roller winding function：
Rolling purpose: Roller press the battery material coated on aluminum foil or copper foil
Maximum opening thickness of rolling mill: 2 mm
Rolling width: Max 300 mm
*Roller winding parameters：
Rolling force: Max. 35T（Can be customized to increase）
Mechanical speed: Max.10m/min
Roll diameter: Ф200 mm；Material：9Cr3Mo
Roller surface hardness: ＞HRC65
Roller surface width: 330 mm
Pushdown mode: Hydraulic
Rolling accuracy: ±2.5 um
Maximum opening of rolling mill: 2 mm
Reducer and gear box: Modular
Rolling mill motor: AC frequency conversion motor
Winding: With correction function and tension control function
*Control System：
Main control system: Touch screen, PLC, servo system
Operation mode:Manual, automatic, emergency stop; the whole machine can be operated before and after
Alarm situation: When the device fails, the touch screen will display the corresponding correction screen
*Hardware accuracy
Scraper: Round jump≤ ± 1.5um, Ra0.4, straightness≤ ± 1.5um
Coating roller (steel roller): Round jump ≤ ± 1.5um, Ra0.4 straightness≤ ± 1.5um
Glue roll: Round jump ≤10um，straightness≤10um
Roll: Round jump ≤ ± 2um, Ra0.4, straightness≤ ± 2um
Deviation correction: ±0.2mm
